Description
Template for Power Distribution unit. Performs application monitoring on PDU bank state, load state, master switch state, outlet state, etc.
Prerequisites
SNMP should be enabled in end device and device should support PowerNet-MIB OIDs and SNMP credentials should be attached against the device in portal.
How to Apply: This template is All instance selection based. It will not ask user to select any instance (s) while assigning it to a device.
Metric Parameters
Parameter | Description |
---|---|
Frequency | Warning Threshold | If the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user. |
Critical Threshold | If the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user. |
Alert | The alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user. |
Metrics
pdu.bank.state
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.12.5.2.1.3 |
Expression | NULL |
Description | Provides the index to the RACK PDU Bank entry and the bank load state. Possible values are 1- Bank Load Normal, 2- Bank Load Low, 3- Bank Load Never Overlaod, 4- Bank Load Overload. [OID: 1.3.6.1.4.1.318.1.1.12.5.2.1.3] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Bank State |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | NULL | Not Applicable |
Warning Operator | EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Warning Threshold | 3 | [{"1":"Normal"},{"2":"Low"},{"3":"NearOverlaod"},{"4":"Overload"}] |
Warning Repeat Count | 1 | 1-12 |
Critical Operator | EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 4 | [{"1":"Normal"},{"2":"Low"},{"3":"NearOverlaod"},{"4":"Overload"}] |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | No | Yes/No |
Sample Output
No graph
pdu.loadbank.config.alarm
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.12.2.4.1.1.5 |
Expression | NULL |
Description | Provides the current bank load alarm state. Possible alarm status values are 1- No Load Alarm, 2- Under Current Alarm, 3- Near Over Current Alarm, 4- Over Current Alarm. [OID: 1.3.6.1.4.1.318.1.1.12.2.4.1.1.5] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Load Bank Configuration Alarm |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | NULL | Not Applicable |
Warning Operator | EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Warning Threshold | 3 | [{"1":"noLoadAlarm"},{"2":"underCurrentAlarm"},{"3":"nearOverCurrentAlarm"},{"4":"overCurrentAlarm"}] |
Warning Repeat Count | 1 | 1-12 |
Critical Operator | EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 4 | [{"1":"noLoadAlarm"},{"2":"underCurrentAlarm"},{"3":"nearOverCurrentAlarm"},{"4":"overCurrentAlarm"}] |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | No | Yes/No |
Sample Output
No graph
pdu.load.state
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.12.2.3.1.1.3 |
Expression | NULL |
Description | Indicates the phase/bank load status. phaseLoadNormal(1) indicates that the phase is operating properly within the rPDULoadConfigLowLoadThreshold and rPDULoadConfigNearOverloadThreshold OID values. phaseLoadLow(2) indicates that the phase load has dropped below the rPDULoadConfigLowLoadThreshold OID value. phaseLoadNearOverload(3) indicates that the phase load is greater than or equal to the rPDULoadConfigNearOverloadThreshold OID value. phaseLoadOverload(4) indicates that the phase load is greater than or equal to the rPDULoadConfigOverloadThreshold OID value. [OID: 1.3.6.1.4.1.318.1.1.12.2.3.1.1.3] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Load State |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | NULL | Not Applicable |
Warning Operator | EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Warning Threshold | 3 | [{"1":"Normal"},{"2":"Low"},{"3":"NearOverload"},{"4":"Overload"}] |
Warning Repeat Count | 1 | 1-12 |
Critical Operator | EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 4 | [{"1":"Normal"},{"2":"Low"},{"3":"NearOverload"},{"4":"Overload"}] |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | No | Yes/No |
Sample Output
No graph
pdu.current.load
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.12.2.3.1.1.2 |
Expression | rPDULoadStatusLoad/10 |
Description | APC PDU phase/bank current load in amps. [OIDs: 1.3.6.1.4.1.318.1.1.12.2.3.1.1.2] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Load State |
Unit | amps |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | NULL | Not Applicable |
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
pdu.outlet.state
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.4.4.2.1.3 |
Expression | NULL |
Description | Provides the name and the state of the outlet. Possible values are 1-Outlet On, 2- Outlet Off, 3- Outlet Reboot, 4- Outlet Unknown, 5- Outlet On With Delay, 6- Outlet Off With Delay, 7- Outlet Reboot With Delay. [OID: 1.3.6.1.4.1.318.1.1.4.4.2.1.3] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Outlet State |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | NULL | Not Applicable |
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | NOT_IN_LIST | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 1,2 | [{"1":"outletOn"},{"2":"outletOff"},{"3":"outletReboot"},{"4":"outletUnknown"},{"5":"outletOnWithDelay"},{"6":"outletOffWithDelay"},{"7":"outletRebootWithDelay"}] |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | No | Yes/No |
Sample Output
pdu.controlled.outlets
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.12.3.1.3.0 |
Expression | NULL |
Description | The number of controlled outlets on this Switched Rack PDU. [OID: 1.3.6.1.4.1.318.1.1.12.3.1.3.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Outlet Statistics |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
pdu.total.outlets
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.12.3.1.4.0 |
Expression | NULL |
Description | The total number of outlets on this Rack PDU. [OID: 1.3.6.1.4.1.318.1.1.12.3.1.4.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Outlet Statistics |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
pdu.monitored.outlets
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.12.3.1.5.0 |
Expression | NULL |
Description | Represents the PDU Outlets Monitored. [OID: 1.3.6.1.4.1.318.1.1.12.3.1.5.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Outlet Statistics |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
pdu.power.supply.status
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.12.4.1.3.0 |
Expression | NULL |
Description | Indicates the PowerSupply alarm. Possible values are 1- All Available Power Supplies OK, 2- Power Supply One Failed, 3- Power Supply Two Failed, 4- Power Supply One and Two Failed. [OID: 1.3.6.1.4.1.318.1.1.12.4.1.3.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Outlet Statistics |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | NOT_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 1 | [{"1":"allAvailablePowerSuppliesOK"},{"2":"powerSupplyOneFailed"},{"3":"powerSupplyTwoFailed"},{"4":"powerSupplyOneandTwoFailed"}] |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | No | Yes/No |
Sample Output
No graph
pdu.master.switch.state
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.318.1.1.4.2.2.0 |
Expression | NULL |
Description | Monitors the status of all outlets. [OID: 1.3.6.1.4.1.318.1.1.4.2.2.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | APC PDU Master Switch State |
Unit | None |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | REGEX_MATCHES | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | .*Off|Unknown.* | 0..255 |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | No | Yes/No |
Sample Output